Ceramic sleeve lined pipe and fitting

Ceramic sleeve lined pipe and fitting include straight pipe, elbow, bending, tee, cross reducer and etc.
Wear Resistant Cylinder Liner Material Alumina Ceramic Tube sleeve

What is ceramic sleeve?

Recently 95% alumina ceramic sleeve lined pipes, elbows and T pipes have been largely applied in lithium battery material conveying system. The main raw material of wear resistant ceramic ring is a special kind of ceramic with AL2O3 as the and the rare metal oxide as the flux, which is melted by high temperature at 1700 °C. The big diameter ceramic sleeve is always a big problem for the ceramic tube manufacturers since it’s very difficult to control the deformation rate of the ceramic sleeve after it’s sintering.

In addition, the flatness of ceramic casing is also an important factor affecting the size of lithium battery materials. We did a lot of analysis and improved our manufacturing techniques to solve both of these problems. Now it can help lithium battery delivery systems better solve these problems, with better material purity, longer service life and better economic benefits.


The combination of high rigidity of ceramic and high elasticity of steel gives the pipe unmatchable features as an abrasion resistant, heat resistant and corrosion resistant material for use in the fields of power generation, metallurgy, mining, and chemical industry etc. It has many advantages over steel pipes, cast stone pipes, and steel-plastic compound pipes.

Read more
Mining port

Related products

ceramic sleeve lined pipe

Sleeve lined process

For different production environments, our company has developed a wear-resistant pipe for a variety of media, based on the temperature, wear and corrosion requirements of the field media, and for the initial application of the scene, our company to provide wear-resistant ceramic ring for the Lined composite straight pipe design to meet the on-site wear resistance, heat resistance and corrosion resistance requirements, in view of this program for the new design (formerly ceramic chip technology, there are many gaps, easy to wear).


Technical index of binder

ItemDataCharacteristics of binder
Density (g/cm3)1.32Megapoxy binder
Compressive strength (MPa)40
Shear Strength MPa26
Impact toughness Kj/m210
Hardness HB9.5
Elastic Modulus GPa2.2
Expansion coefficient 10-6/℃20.1
Softening temperature℃263
Coking temperature℃335
Acid resistance(24H)StabilityTest solution : 15%H2SO4
Alkali resistance(24H)StabilityTest solution: NaOH
We use the Australian Megapoxy high strength structural adhesive, this structural glue is modified epoxy resin polymer, anti-aging ability, and wear-resistant ceramic bonding to form a strong and cushion of the anti-wear layer, cured water, anti-corrosion performance is excellent, toughness, displacement-resistant effect is remarkable.

Delivery abrasion resistant pipe
on site installation photo of ceramic tile lined pipe and fittings 01

Transport and installation precautions

Matters needing attention for transportation and installation of ceramic pipe

The ceramic composite pipe has high hardness and good toughness, but it should be put gently in the process of transportation and installation to avoid serious collision, especially to avoid direct contact with metal instruments or impact on the ceramic layer on the end surface.

The ceramic lined bending pipe is installed with directivity. When the bending pipe is installed, the direction indicated by the arrow on the surface of the bending pipe should be consistent with the flow direction of the conveying medium.

When installing the pipe, the pipe should be aligned with the center line and level should be adjusted to make sure that both ends meet accurately.The displacement of both ends should be controlled within 1.0mm.

When the flexible pipe joint is used to connect and install the pipe, the inserted lengths of both ends of the flexible pipe joint shall be adjusted symmetrically.Since the thermal expansion coefficient of the composite pipe is about 1/3 of that of steel, the expansion clearance can be reduced by 3-5mm.

When using flange connection, the flange end shall be flush with the end of the composite pipe.

Due to the excellent welding performance of the composite pipe, the pipe connection can be conducted by welding. However, when welding, 45o-60o “V” type slope Angle is 2-4mm and gap is 0.8-1.2mm.

Frequently Asked Questions


How long is your delivery time?

The delivery time of customized products is generally 25 35 days, and non customized products are generally shipped within 24 hours after payment.

What are your payment terms?

T/T 30% as the deposit,The balance payment is paid in full before shipment

What is your minimum order quantity?

There is no minimum order quantity requirement. Customized products are tailor made according to the drawings provided by the customer.

Do you provide samples? Is it free?

If the value of the sample is low, we will provide it for free, but the freight needs to be paid by the customer. But for some high value samples, we need to charge a fee.

What is the packaging and transportation form?

Non steaming wooden box and iron frame packaging. Special packaging is available according to customer needs. The transportation is mainly by sea.


As part of our quality regimen, 100% of incoming raw materials, semi-finished products, as well as finished products are thoroughly inspected prior to being entered into our inventory. We have established multiple hold points throughout fabrication as well as a comprehensive final inspection for all products.